A novel bio‐based phthalonitrile resin derived from catechin: synthesis and comparison of curing behavior with petroleum‐based counterpart

The development of bio‐based thermosetting resins with good thermal stability can potentially afford sustainable polymers as replacements for petroleum‐based polymers. We report a practical route to a novel catechin‐based phthalonitrile resin precursor (CA‐Ph), which contains free phenolic hydroxyl groups that result in ‘self‐curing’ at elevated temperatures to afford a thermostable polymer. Comparison of the performance of this CA‐Ph resin with that of a conventional petroleum‐based bisphenol A phthalonitrile resin (BPA‐Ph; containing 5 wt% of the curing agent 4,4′‐diaminodiphenylsulfone) revealed that CA‐Ph exhibits a lower melting point and curing temperature. Cured CA‐Ph resin retains 95% of its weight at 520 °C under a nitrogen atmosphere, which compares favorably with results obtained for BPA‐Ph resin that retains 95% of its weight at a lower temperature of 484 °C. Kinetic results indicated that the curing reactions of both CA‐Ph and BPA‐Ph systems follow an autocatalytic mechanism. These results suggest that catechin is a useful bio‐based feedstock for the preparation of self‐curing and thermally stable phthalonitrile resins for advanced technological applications. © 2017 Society of Chemical Industry     

釉面分相对无铅CuO-MnO2系金属光泽釉的影响

以钙系生料釉为基础,引入结晶剂CuO、MnO₂制备无铅CuO-MnO₂系金属光泽釉;结合XRD、SEM-EDS进行物相组成定性分析和显微结构表征,系统探究外加TiO₂、V₂O₅以及玻璃粉对金属光泽釉釉面分相的影响。研究表明:一定量的TiO₂、V₂O₅引入能有效促进釉面的分相,将玻璃粉部分替换基础釉中的钾长石能使得釉熔体的高温粘度降低,并进一步加剧釉面分相,促进CuMn₂O₄铜锰尖晶石在釉层表面的析出和富集;当TiO₂引入量为2%,V₂O₅引入量为1%,玻璃粉引入量为25%(同为质量分数)时,金属光泽釉釉面效果最佳。     

-15℃下Na+， K+， Mg2+//Cl-， NO3-， SO42——H2O体系相平衡研究

新疆卤水硝酸盐矿主要含有Na⁺、K⁺、Mg²⁺、Cl^-、NO₃^-、SO₄^2-六种离子，属于高元复杂体系，其合理利用和开发需要不同温度下的相平衡研究作为理论支撑。采用等温溶解平衡法，对Na⁺， K⁺， Mg²⁺//Cl^-， NO₃^-， SO₄^2--H₂O体系在-15℃、NaCl·2H₂O饱和条件下的相平衡进行了研究，并构建了相图。相图中有六个零变量点和八个两盐结晶区，只存在一种复盐KCl·MgCl₂·6H₂O。八个两盐结晶区，分别对应于NaCl·2H₂O+Na₂SO₄·10H₂O、NaCl·2H₂O+NaNO₃、NaCl·2H₂O+KCl、NaCl·2H₂O+KNO₃、NaCl·2H₂O+MgSO₄·7H₂O、NaCl·2H₂O+MgCl₂·8H₂O、NaCl·2H₂O+Mg(NO₃)₂·6H₂O和NaCl·2H₂O+KCl·MgCl₂·6H₂O，其中NaCl·2H₂O+Na₂SO₄·10H₂O共晶区最大，在低温时，硫酸钠的溶解度最小，降温过程中较易结晶析出。与该体系在25℃下的相图相比，复盐种类减少5种，零变量点减少19个，相关系得以极大简化。     

内插法在相关干涉仪测向体制中的应用

测向误差的减小一直以来都是无线电测向精度提高的一个难点,对于不同的测向体制所采用的减小测向误差的方法都不尽相同。本文主要介绍的是相关干涉仪测向体制的基本原理以及通过内插法的应用来减小测向误差的方法。     

Design and optimization of ceramic membrane structure: From the perspective of flux matching between support and membrane

The support flux was first investigated as a separate influencing factor for its effect on performances of ceramic filtration membranes. Three pre-membranes were prepared by tape-casting and then transfer-coated to supports to form dual-layer ceramic membranes after sintering. Experiments demonstrated that membrane layers with almost the same properties were obtained despite the huge difference in support flux. When the support flux increases from 3.120 to 97.53 m³m^?2h^?1, the flux of these three membrane series have increased by 75%, 186% and 228%, respectively. Experimental rules can provide structural design and evaluation from the perspective of permeability. The limit membrane flux of a certain system was derived according to the resistance distribution law of internal membrane structure and the Darcy's theorem. On this basis, a method for designing support flux was proposed. Furthermore, we present a criterion to quickly and easily evaluate the match between the support and the top layer, which is the ratio of membrane resistance to total resistance. Finally, the filtration resistance of penetration caused by suction of membrane particles into the support was measured for the first time, taking the advantage of the transfer-coating method that inherently free of penetration. Our works are expected to deepen the understanding of the ceramic membrane structure and provided guidance for its rational design and optimization.     

基于子系统的非线性时变系统辨识方法

针对非线性时变系统提出一种基于子系统的辨识方法，用于时变多自由度（multiple degree-of-freedom，简称MDOF）系统中非线性的定位和估计，并且无需关于系统的先验知识。所提出的新方法提供一个连续时间模型，MDOF系统按照自由度被分解为不同的子系统。设计正交化算法和误差减小率（error reduction ratio, 简称ERR），可以确定子系统中质量和自由度之间的线性及非线性连接的所有信息。在辨识过程中，时变参数的时间表达式可以由新方法准确给出。用一个3自由度（degree-of-freedom, 简称DOF）集中质量系统和一个机械臂结构的辨识过程为例，对所提出的方法进行验证。由于简单性及高效性，此方法将在实际工程中取得广泛的应用。     

一种汽车顶盖抗雪压动态仿真分析方法

目前顶盖雪压静态仿真分析方法的雪压计算值与测试值存在偏差,并且不能反映顶盖实际变形的位置和整体变形模式。为改进静态仿真分析方法,提出一种非线性显式计算的动态仿真分析方法,并以某乘用车为例,通过试验验证了其可靠性及有效性,为顶盖的研发设计提供了参考。